ITachFlexEthernetPoE discovery incorrectly reports Sensor

I have a iTach Flex Ethernet PoE device with the cable configured for Infrared, three IR port = no, and Blaster = yes. Based on logging it looks like the device is being detected correctly (see below). However, the device list thinks it is a Sensor (Name = "iTachFlexEthernetPoE Sensor 1", Type = "Sensor"). I assuming the Type should be "Blaster" or "IR" or something similar. Is a driver change required to resolve this or can I change the Type field.

Log messages with Verbose logging enabled:
23/02/2024 22:23:10.23 · DEBUG · Server.doCommand - GenericIR|discovery~toggle from dashboard-fx-ergv
23/02/2024 22:23:10.23 · DEBUG · GenericIR.doCommand - Cmd=[discovery~toggle] Client=[dashboard-fx-ergv]
23/02/2024 22:23:13.23 · DEBUG · GenericIR.Discover RX - AMXB<-UUID=GlobalCache_000C1E065A22><-SDKClass=Utility><-Make=GlobalCache><-Model=iTachFlexEthernetPoE><-Revision=710-3000-21><-Pkg_Level=><-Config-URL=http://172.16.1.59><-PCB_PN=025-0035-15><-Status=Ready>^
23/02/2024 22:23:13.23 · DEBUG · Server.WebCmd - Refreshgrids23/02/2024 22:23:13.23 · DEBUG · GenericIR.NetConnect - Device (1) has connected.
23/02/2024 22:23:14.23 · DEBUG · GenericIR.TX >>> - iTachFlexEthernetPoE:getdevices
23/02/2024 22:23:15.23 · DEBUG · GenericIR.RX - iTachFlexEthernetPoE(1) [device,0,0 ETHERNET]
23/02/2024 22:23:15.23 · DEBUG · GenericIR.RX - iTachFlexEthernetPoE(1) [device,1,1 IR_BLASTER]
23/02/2024 22:23:15.23 · DEBUG · GenericIR.RX - iTachFlexEthernetPoE(1) [endlistdevices]
23/02/2024 22:23:20.23 · DEBUG · Server.doCommand - GenericIR|discovery~toggle from dashboard-fx-ergv
23/02/2024 22:23:20.23 · DEBUG · GenericIR.doCommand - Cmd=[discovery~toggle] Client=[dashboard-fx-ergv] 
 
 

I would appreciate a response to the above post. The iTach Flex Ethernet PoE device appears to be detected correctly based on its configuration (infrared, three IR port = no, Blaster = yes). The device list reports type as a "Sensor". Can I change the type field to make this work or is a driver change required? If changing the type field is all that is required, what type should I make it (IR, Blaster, IR_Blaster)? I want to make sure the configuration is correct, before I spend more time trying to debug this.

05/04/2024 21:23:29.23 · DEBUG · GenericIR.NetConnect - Device (1) has connected.
05/04/2024 21:23:30.23 · DEBUG · GenericIR.TX >>> - iTachFlexEthernetPoE:getdevices
05/04/2024 21:23:30.23 · DEBUG · GenericIR.RX - iTachFlexEthernetPoE(1) [device,0,0 ETHERNET]
05/04/2024 21:23:30.23 · DEBUG · GenericIR.RX - iTachFlexEthernetPoE(1) [device,1,1 IR_BLASTER]
05/04/2024 21:23:30.23 · DEBUG · GenericIR.RX - iTachFlexEthernetPoE(1) [endlistdevices]

Flex's are a bit tricky to discover. What I did was remote in and manually add an ITachIR using the ip address of the flex. You now have the three IR ports available for use.